Remove Brick Mortar TIPS
- Muriatic acid is best – dilute it
- Scrape off excess mortar smear
- Wet brick before acid application
- Allow acid to bubble for minutes
- CLICK HERE to Get Tim’s FREE & FUNNY Newsletter!
DEAR TIM: How can I remove brick mortar from the sidewalk I just constructed with paver bricks? My husband and I got the mortar smeared on the brick, and it looks terrible.
What methods can I use so the brick is not damaged?
Is there a non-toxic way to do this repair? Sarah H., Kingsport, TN
DEAR SARAH: Smeared mortar on brick pavers, as well as brick walls, is a very common problem. It seems to be a growing problem as many masons don’t seem to take pride in their work. It’s understandable for DIYrs to make a mess.
Depending upon the type of brick, the job can be simple or a nightmare. It is my hope that you do not have a deeply grooved wire-cut brick, as these have many small crevices that can make cleaning a career choice.
Since you are concerned about the toxicity of different options, you may find it very hard to do this job. You can use certain acids that are more aggressive than others, and the ones that work faster tend to be more toxic.
But don’t panic as you may discover that an aggressive acid treatment may work for you if you work to control the amount of liquid used as you work.
Typically bricklayers will use muriatic acid to dissolve mortar from most brick. This is simply a form of hydrochloric acid.
When you purchase this product it often has a skull and crossbones on the label warning you that it is a powerful chemical.
But these products can be neutralized. That’s something all of us should have discovered in our high-school chemistry class.
In fact, the mortar does neutralize the acid as it works. That’s one of the benefits of choosing to use muriatic acid.
As long as you don’t go splashing it around and use too much, it’s not that toxic. Plus, once diluted with water, it becomes even more safe.
There are other acids that will react and dissolve the alkaline chemicals in the mortar. Even white vinegar that is in your kitchen will work to some degree.
Since you eat vinegar in many foods, you know it’s not a toxic acid.
The challenge for you is finding an acid somewhere between vinegar and hydrochloric acid that will efficiently remove the mortar buildup.
If you’re really worried about the toxicity of muriatic acid, and you shouldn’t be, you should consider calling a physical chemistry professor at a local college or high school.
You can also visit a building supply company to see if they stock a non-toxic acid that will dissolve the mortar.
Remove Excess Mortar
The first step in the process is to remove as much of the mortar as possible with a scraper or chisel without scratching the brick face. Clear water flowing over the brick acts as an effective lubricant that will minimize damage to the brick.
I’ve had great luck using a 3-inch-wide stiff scraper with a chiseled edge.
If you have to tap the scraper with a hammer, do so at a low angle with the face of the scraper nearly parallel with the face of the brick. You are trying to get the mortar film to a thickness less than that of a plastic credit card.
Bathe The Brick
Once the majority of the mortar is off the brick, you then should consider bathing the brick with a diluted acid solution. As mentioned before, muriatic acid is highly effective, and it works on most brick.
Usually you mix one part of the acid with ten parts of clean water. Always read the instructions on the acid label and pay particular attention to all safety instructions.
IMPORTANT TIP: It’s also a good idea to contact the manufacturer of the brick. Some brick can be damaged and discolored by acids. It’s really worth the effort to call the brick manufacturer if possible.
Wet The Brick
I’ve found in most cases you should dampen the brick with clear water before you apply the acid solution. Always try this in an out-of-the-way area if you are unsure if the acid will harm the brick.
If you don’t do this, it’s possible to burn the brick. Some brick don’t like muriatic acid and it can discolor them.
Be sure to TEST the acid on the brick in an out-of-the-way location.
Bubble & Fizz
If you use muriatic acid, you should see tiny bubbles forming where the solution contacts the smeared mortar. This tells you that the acid is reacting with the mortar paste and is starting to dissolve it into the liquid solution.
Use a scrub brush to help remove the mortar. Wait five or ten minutes after the acid solution has been applied to the brick before you scrub. Allow the acid to do much of the work for you.
It can take multiple applications of acid solution to remove all of the mortar. Rinse the acid solution from the brick with massive amounts of water. The more water you use, the better.
Working with acid solutions is very tricky. You can hurt yourself, your clothes, your brick, the new mortar and vegetation around your home. If you have valuable vegetation and landscaping, you should try to stop any acid solution from getting into the soil.
Be sure to wear all of the protective gear to prevent burns to your skin and eyes. Muriatic acid straight from the bottle is a wicked liquid. The fumes are very toxic, and it can cause serious burns to your skin very quickly. Do not underestimate this chemical.
Wait 30 Days
I would not ever use muriatic acid on fresh mortar. Allow the mortar to cure a minimum of thirty days before you attempt to acid wash it.
That said, if you get mortar on brick you should immediately try to scrape it off or brush it off. If there’s a thin mortar paste that has no sand in it, that will easily and quickly be removed with mild acids like vinegar.
Harsh acids will attack the fresh mortar between the brick that you do not want to remove.